Heavy Duty Double Shaft Cone Pulley Lathe Machine
Quick Contact
DOUBLE SHAFT LATHE MACHINE is the most useful and indispencable lathe machine for engineering workshop,as it has set two separate mechanisam for turning and threading for working independently,so the operarion of threading threading shaft will work and while turning operation turning shaft will work, and so that it can get better accuracy.
Bed:-The bed is made of high graded casting and its heat treated with high quality induction hardened and grounded to opt long lasting life, after it well machined.the design of bed very sturdy to resist any kind of vibration.
Head Stock:-The head stock is made of good quality graded cast iron material and it is well machined,The spindle is made good alloy steel and its fully heat treated and grounded,it runs on best quality bearings, and bushes where and when it requires.
Carriage: The carriage is located between the headstock and tailstock and serves the purpose of supporting, guiding and feeding the tool against the job during operation.
Tail Stock:- the tailstock is made of good quality graded cast iron material and it is well machined,maintained its alignment with head stock to getting best accuracy.tailstock spindle is made good alloy steel ,fully heat treated and grounded,
Legs: The legs carry the entire load of machine and are firmly secured to floor by foundation bolts.
Special Features
- ood Quality graded casting with high quality hardened and grounded bed ways to resist wear and tear and get extra long life.
Main spindle and Tail stoke spindle will be hardened and grounded.
Pulleys and gears are to be Dynamically balanced.
Fully oil bath Appron gear box.
Steel parts are made of Alloy Steel.
Bushes are made of Gun Metal Material.
Standard Accessories
- Flame hardened and grounded bed ways.
Chuck back plate
Center adapter
Live and Dead center
Tool Post Spanner
Motor Pulley
Norton Gear Box(Quick Change Gear box)
Safety Guards
Extra Accessories
- Face plate
Carrier plate
Steady rest , Follow rest
Taper Turning Attachment
Motorised Coolant pump and its tank
Rear Tool Post
Electrification
Specification
| Model | BL-0/DSHD-330 | BL-1/DSHD-330 | BL-2/DSHD-330 |
|---|---|---|---|
| Admit bet. Center in mm | 525 (20½" inch) | ||
| Length of Bed in mm | 1675 (5½ ft) | 2135 (7 ft) | 2745(9 ft) |
| Width of bed in mm | 330 (13" inch) | 330 (13" inch) | 330 (13" inch) |
| Height of Centre in mm | 254 (10"inch) | 254 (10"inch) | 254 (10"inch) |
| Swing over bed in mm | 505(19¾ inch) | 505(19¾ inch) | 505(19¾ inch) |
| Swing over cross slide in mm | 300(11¾ inch) | 300(11¾ inch) | 300(11¾ inch) |
| Swing in gap in mm | 805(31½" inch) | 805(31½" inch) | 805(31½" inch) |
| Length of gap IFO face plate in mm | 190(7½" inch) | 190(7½" inch) | 190(7½" inch) |
| MAIN SPINDLE | |||
| Type & Size of Spindle Nose | Threaded | Threaded | Threaded |
| Spindle Bore in mm | 52 (2 1/8" inch) | 52 (2 1/8" inch) | 52 (2 1/8" inch) |
| No of Speed/Range in RPM | 8/26 TO 465 RPM | 8/26 TO 465 RPM | 8/26 TO 465 RPM |
| Morse Taper | MT/6 | MT/6 | MT/6 |
| TAIL STOCK | |||
| Diameter of Spindle (RAM) | 51.8(2" inch) | 51.8(2" inch) | 51.8(2" inch) |
| Travelling of Spindle (RAM) | 180 (7" INCH) | 180 (7" INCH) | 180 (7" INCH) |
| Morse Taper of Spindle (RAM) | MT/4 | MT/4 | MT/4 |
| LEAD SCREW | |||
| Diameter of Lead Screw / TPI | 38.1(1½" inch) | 38.1(1½" inch) | 38.1(1½" inch) |
| Diameter of Shaft | 31.75(1¼" inch) | 31.75(1¼" inch) | 31.75(1¼" inch) |
| THREADS | |||
| No of Threads / Range in inch (BRITISH STANDARD) | 44/2 TO 60 TPI | 44/2 TO 60 TPI | 44/2 TO 60 TPI |
| No.of Threads / Range in mm(METRIC STANDARD)) | 24/0.5 TO 15 PITCH | 24/0.5 TO 15 PITCH | 24/0.5 TO 15 PITCH |
| Floor Space Occupied in mm | 2200 X 1450 | 2660 X 1450 | 3260 X 1450 |
| Approx. Weight in Kgs | 1200 KG | 1300 KG | 1400 KG |
| Approx. Case Dimensions in mm | 2400X1300X1600 | 2850X1300X1600 | 3350X1300X1600 |
