Excel Series Medium Duty Twin Lead Screw Cone Pulley Lathe Machine
Quick Contact
THREADING is the most critical operation to do on the lathe machine.but our this TWIN LEAD SCREW CONE PULLEY LATHE MACHINE will do it lot more easier and proove time saver for you.
This is our most unique lathe machine,which has mounted two LEADSCREW , one LEAD SCREW has ( british standard) THREAD PER INCH,while other one has (metric standard) PITCH in MM. and so that this machine can doing both type of thread with out changing any setting
Bed:-The bed is made of high graded casting and its heat treated with high quality induction hardened and grounded to opt long lasting life, after it well machined.the design of bed very sturdy to resist any kind of vibration.
Head Stock:-The head stock is made of good quality graded cast iron material and it is well machined,The spindle is made good alloy steel and its fully heat treated and grounded,it runs on best quality bearings, and bushes where and when it requires.
Carriage: The carriage is located between the headstock and tailstock and serves the purpose of supporting, guiding and feeding the tool against the job during operation.
Tail Stock:- the tailstock is made of good quality graded cast iron material and it is well machined,maintained its alignment with head stock to getting best accuracy.tailstock spindle is made good alloy steel ,fully heat treated and grounded,
Legs: The legs carry the entire load of machine and are firmly secured to floor by foundation bolts.
Special Features
- Good quality graded casting with high quality hardened and grounded bed ways to resist wear and tear.
Main spindle and Tail stoke spindle will be hardened and grounded.
Pulleys and gears are to be Dynamically balanced.
Fully oil bath Appron Gear box.
Steel parts are made of Alloy Steel.
Bushes are made of Gun Metal Material.
Standard Accessories
- Flame hardened bed ways
Chuck back plate
center adapter
Live and Dead center
Tool post Spanner
Motor Pulley
Gear set for British and Metric Threading
Safety Guards
Extra Accessories
- Face plate
Carrier plate
Steady rest, Follow rest
Taper turning attachment
Motorised Coolant Pump and its tank
Rear Tool Post
Norton gear box (Quick change box)
Electrification
Specification
| Model | BL-1/TLSMD | BL-2/TLSMD | BL-3/TLSMD |
|---|---|---|---|
| Admit bet. Center in mm | 475 (18¾ inch) | 750 (29½ inch) | 925 (36½ inch) |
| Length of Bed in mm | 1370 (4½ Ft) | 1600 (5¼ Ft) | 1825 (6 Ft) |
| Width of bed in mm | 277 (11 inch) | 277 (11 inch) | 277 (11 inch) |
| Height of Centre in mm | 240 (9½ inch) | 240 (9½ inch) | 240 (9½ inch) |
| Swing over bed in mm | 475 (18¾ inch) | 475 (18¾ inch) | 475 (18¾ inch) |
| Swing over cross slide in mm | 265 (10½ inch) | 265 (10½ inch) | 265 (10½ inch) |
| Swing in gap in mm | 735 (28¾ inch) | 735 (28¾ inch) | 735 (28¾ inch) |
| Length of gap IFO face plate in mm | 115 (4½ inch) | 115 (4½ inch) | 115 (4½ inch) |
| MAIN SPINDLE | |||
| Type & Size of Spindle Nose | Threaded | Threaded | Threaded |
| Spindle Bore in mm | 52 or 80(2 inch or 3 inch) | 52 or 80(2 inch or 3 inch) | 52 or 80(2 inch or 3 inch) |
| No of Speed/Range in RPM | 6/42 to 550 | 6/42 to 550 | 6/42 to 550 |
| Morse Taper | MT-6 | MT-6 | MT-6 |
| TAIL STOCK | |||
| Diameter of Spindle (RAM) | 51 (2 inch) | 51 (2 inch) | 51 (2 inch) |
| Travelling of Spindle (RAM) | 135 (5¼ inch) | 135 (5¼ inch) | 135 (5¼ inch) |
| Morse Taper of Spindle (RAM) | MT-4 | MT-4 | MT-4 |
| LEAD SCREW | |||
| Diameter of Lead Screw / TPI | 31.75 (1¼ inch) | 31.75 (1¼ inch) | 31.75 (1¼ inch) |
| Diameter of Lead Screw / PITCH | 31.75 (1¼ inch) | 31.75 (1¼ inch) | 31.75 (1¼ inch) |
| No of Threads / Range in inch | 29/4 to 48 TPI | 29/4 to 48 TPI | 29/4 to 48 TPI |
| No.of Threads / Range in mm | 20/0.5 to 7.5 mm | 20/0.5 to 7.5 mm | 20/0.5 to 7.5 mm |
| Floor Space Occupied in mm | 1500 x 850 | 1750 x 850 | 2200 x 850 |
| Approx. Weight in Kgs | 500 | 550 | 600 |
| Approx. Case Dimensions in mm | 1700 x 900 x 1350 | 1950 x 900 x 1350 | 2400 x 900 x 1350 |
